This grinding wheel is for all types of skate blades. S-4/KB60 is to be used on a SSM PROFIL.
This grinding wheel is for all types of skate blades. S2/KB60 is to be used on a SSM-2. Dark Blue
This is our most efficiant grinding wheel that works fantastic on all types of skate blades . Recommended for shops. S-2/ME60 is to be used on a SSM-2 .
This new high performance wheel works excellently on all types of skate blades. S-2/HP70 is to be used on a SSM-2.
This superb grinding wheel works on all types of skate blades. This high quality ceramic wheel is similar to the KB60 and HP70 in heat and durability properties. With finer grit it leaves a little finer finish but does not cut as strongly as the lower grit wheels.
S-2/KB80 is to be used on a SSM-2.
150 x 6 mm, Ceramic grit, size 60 or 80 for SSM-2 (Blue/Light Blue)
This standard grinding wheel is primarily for skates with a skate blade of carbon steel. S-2/60 is to be used on a SSM-2.
Diamond dresser with a synthetic diamond rod having a square cross section.
Its new design makes it sharp during its whole lifetime. Only for the flat surface device on the right side of the SSM-2.
Diamond dresser with a natural diamond of fine quality. Last approximately 3-4 grinding wheels. Grinding wheel on average good for 300-350 sharpening’s.
Fits both the flat and hollow surface devices of the SSM-2 and SSM PROFIL.
Diamond dresser with a synthetic diamond rod having a square cross section. Its new design makes it sharp during its whole lifetime. Fits both the flat and hollow surface devices of the SSM-2 and SSM PROFIL.
Whetstone silicon carbide
Whetstone (Aluminum Oxide)
Different grit sizes
Ceramic whetstone made of silicon carbide.
It has the same grit size on both sides.
Diamond hand hone. Precision tool. Handle with care!
Skate Blade Accessories
New Skate Blade Controller (SBC) Blade Hollow and Thickness$32.00
For checking the Blade Thickness and hollowness underneath a skate blade we recommend using the SBC.
Blade Edge Checker$70.00
This tool allows fast checking if you have even edges underneath the skate blade. You attach both parts as pictured. If the outer edges are even, then the part that is lying on the skate blade edges will be parallel to the line on the other part. Otherwise the edges are uneven.
Now built with a hardened layer to improve strength and durability!
Blade Straightener – SKR$99.00
This tool is for temporarily bending back a skate blade that has been hit and deformed during a game. Insert the bent part between the ball bearings and press down the upper bearing to get the blade straight. Adjustable rollers and can be mounted to work bench.
Figure Skating Hooks – FH$44.00
Figure skating hooks for the upper lace holes on figure skates . Available in white or black color.
Bag of 100.
Eyelets – EL$46.00
Eyelets for the lace-holes on skates. Available in black color.
Bag of 100.
Copper Rivets – KN$50.00
Copper Rivets + washers for attaching blades on skates. Solid.
Rivets – SN$9.00
Bag of 100.
Tube rivets for attaching blades on skates. Available in lengths 8,10, 12, 14, 16, 18,20,22 and 24 mm . (0.32,0.40,0.48,0.55,0.63,0 . 71,0 . 79,0.87 and 0.95 inch.) Head is 1/4 inch diameter, Tube diameter 1/8 inch
Tool Holder #30 for NM 11$227.00
This hook together with tool set N-21 can be used on the belt buckles of ski boots for processing tube rivets . It can also be used together with tool 28 and tool 29 for larger rivets Uoint rivets with a size up to 025 mm) located on the sides of ski boots.
N-41 is used for stretching a boot or a skate shoe so that it will better fit the foot.
N-RE is used for removing eyelets from skates.
N-E is also included when buying a NM-11/21. It is used for mounting eyelets into lace-holes .
N-21 is included when buying a NM-11/21 . It is used when changing skate blades to remove tube rivets , to attach copper rivets and tube rivets . Copper rivets are removed by cutting them apart with cutting pliers